User Log On
GalleryGalleryGalleryGalleryGallery
Divinity MBC Bible Institute
What are the three main reasons for the slow discharge of the sand making machine?
   Discussion: What are the three main reasons for the slow discharge of the sand making machine?
crushermachine169 · 5 years, 2 months ago
=12px[color=#000000]1. The blockage of the sand making machine may be caused by the excessive speed of the feeding. When the feeding speed is too fast, the load of the sand making machine will increase, and the material that cannot be processed in time will be slow or even discharged. The problem of blocking material. In this case, always pay attention to the speed of the feeding and the pointer of the current meter of the sand making machine. When the feeding is large, the pointer of the current meter of the sand making machine will be too large. When the rated current of the equipment is exceeded, it will cause Overloading, when working in this situation for too long, can cause the motor to block or even burn the equipment. When this happens, on the one hand, the feed amount should be reduced immediately, and the adjustment can be made by adjusting the feeding device. Therefore, when selecting equipment, it is necessary to select suitable equipment, so as to ensure that the sand making machine can ensure safe and effective work in the production process.[/color]=12px[color=#000000]2. When the sand making machine works for a period of time, problems such as aging, breakage, screen closing, and crushing of the corresponding parts may occur, or when the water content of the material crushed by the sand making machine is large, the equipment may be discharged slowly or even The problem of blocking material, in this case, it is necessary to regularly check the equipment, maintain and replace the relevant accessories of the sand making machine in time to ensure the safe, stable and efficient operation of the equipment. Under normal circumstances, the water content of the crushed and crushed materials of the sand making machine should be controlled below 14%. After working for a period of time, the equipment should be maintained and repaired.[/color]=12px[color=#000000]3. The problem that causes the sander to discharge slowly or block is the clogging of the vent. This situation may be caused by the failure of the corresponding conveying equipment. When the problem is found, the vent should be cleaned first, and then replaced in time. Corresponding conveying equipment, adjust the equipment to achieve the best fit, and ensure the normal and stable operation of the sand making machine during the working process.[/color]
vynalori · 3 years, 7 months ago
сайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайт сайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайт сайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайт сайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайт сайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайт сайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайт сайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайт сайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайт сайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайт сайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтсайтtuchkasсайтсайт

You must first create an account to post.


© 2024, Divinity MBC Bible Institute
yahoo.com@Divinityinstitute
Welcome, guest!
Church Websites